Late on the reply. I have usually replaced with a plexiglass type material. For those of you running glass, buy another windshield support pole, measure and cut so that it fits when placed in the...
Type: Posts; User: xrover
Late on the reply. I have usually replaced with a plexiglass type material. For those of you running glass, buy another windshield support pole, measure and cut so that it fits when placed in the...
I've been off the board for a while, but still out and about in the avenger. Is anyone planning a fall colour trip in South/Near North Ontario?
Tks
Len
I prefer to just go and ride and learn how to recover my vehicle. Any vehicle will and can get stuck, so knowing more about how to get it out safely is more important to me than getting it stuck an...
2004 used the 674cc, Kohler four-cycle engine.
The 31hp Kohler engine came in EFI, but this is the most recent.
So perhaps someone upgraded the engine?
There was an "Avenger" list for sale on...
Any chance you got mud splashed up on the exhaust pipe. That makes a new smell to many folks.
On our 3rd Argo and pretty much like everyone else says, an ounce of prevention........oh, and bearings. Keep they lubed and more importantly keep your ears tuned to changes in the sound it makes....
Don't touch it! We've had a Conquest and an Avenger, one air cooled, one water cooled, the muffler gets just as hot (well at least seems just as hot). The fact it is so in your face probably makes...
As stated, if changing outside bearings, might as well do the inside now as well. They are that cheap.
On the carb, do the rebuild and use a capful of gas conditioner for every tank. You won;t have...
Having had 3 hubs tear off an axle while deep in the bush, I would recommend not leaving on extensions. In my case it was with rubber tracks, and at different times, but it's quite the pain to limp...
I think he makes a track that will fit over the 24" Frontier tire on a bigfoot.
As for power, now problem, but I did find the tracks sapped about 40% of the speed. The newer tranny...
Saw a larger Kaw put into an Avenger. The hood needed to be modified to take the extra height but I was not around when that was done.
Maybe anti-seize would be better to use. I don't think I ever had a problem with a screw coming out, but lot's of issues of trying to get one out.
Have you replaced the fuel filter lately? We had ours replaced and was restricting flow of gas. It ended up being a non-genuine Kholer fuel filter that did it to our machine. I always ensure we...
I am considering looking at one of these for the front seats. In an Argo, when you consider where your butt is, this seat should fit in quite nice. May need some bracket modification but could be a...
Sure thing. I only have a couple of pictures where you can see them. I still only have the 2.
MobileMe Gallery
p.s. I am not in any of these photos. Tires are on the Avenger.
In the truck world we always go for double the gross vehicle weight for winch and line strength. I recently switched to synthetic line over steel cable, much lighter and not so dangerous if it...
That looks great. Are you close to the GTA so some of us locals can check it out?
As for engine kill, you will either need to set up a kill switch for the fuel pump (maybe use a battery kills...
You should be fine with the battery, it's the starter motor that needs the torque. I assume the engine comes with it's own starter motor. If not, then you should upgrade to a higher torque motor. A...
I would not go over 1 psi. B&S has a pump which I would recommend. I put one on my Bigfoot and it worked very well. But I then ran into battery generator problems. No battery, no fuel. So I would...
Not sure if this was covered in the thread but Argo changed the tensioners for the 07 and up model year (some late 06 may have got them as well). The original tensioners had very small steps on them...