Search:

Hi make sure you change the chains. dont leave Them to long. the chains can stretch
and then lay on the floor and wear a hole through the body. It happened to me.

Hi I had same problem with my avenger. Take the teeth out of the grease gun nozzle. Screw the end cap off the gun nozzle remove the teeth and reinstall the end cap.
The gun will still work but you...

Hi, Yes you can use 5/16 bolts. make sure you use bolts that are loNG enough. you will have to cut one flat off the hex part of
the bolt to make room to slide past the sprocket body. The thread end...

Hi, If you are going to get into the Argo business I would not buy a Argo older than 1989. the older Argos do not have splined axles. The ones you may be buying have axles that have roll pins that...

Hi, When buying tires if you may buy tracks or have tracks not all tires will fit in some tracks.
keep this in mind. Hope this helps.

Hi , This will help. I had the same problem with my Avenger. I greased the axle seals on the out side of the body.
The grease fitting pulled out. I removed the teeth in the grease fitting at the end...

Hi, I have a avenger Argo I tie mine down this way. First I took the bolt under the wench which goes through the body
and helps hold the wench bracket in place in the engine compartment.I replace...

well i read your post including the part where your front right wheel studs sheared off. I had the same experence with an Argo I drive on occasion
the Argo is owned by a Ground Search & Rescue Team...

Hi, if you are running tracks on your Argo or are going to keep this in mind when buying tires. Some tires
do not fit some tracks. A little info for you. Paul

Hi, I use Castrol Chain Lube. This is what my dealer said to use. Works great, spray can. Keeps the chains wet all the time. Don't use motor oi or grease
you will ruin your chains. Hope this helps.

Hi,
Take a floor jack and jack up the front of the Argo. Put a piece of plywood on the jack end so it wont damage the under body when lifting. Do this at each end of the Argo. Check for movement in...

Hi, just a little info on tires. If you are planing on using tracks on your Argo some tries will
not fit in the tracks. Keep this in mind when buying tires. Regards Paul.

Hi, I don't know if you found the proper shear pins or not. I read in the past that argo owners
have used 5/16 bolts instead. The bolts have to be modified by cutting of one side of the head off...

Hi, The engine you have has a electric fuel pump and a fuel filter. These are located under the seat on top of the fuel tank.
I would check these out to make sure you have fuel flow. Regards...

Hi, This may help in your tire choice. If you are running tracks or may be in the future. Make sure
your tire type will allow you to use tracks. Some tracks do not fit over some tires. Hope this...

Hi, Here is some info that may help. Do you have a spacer coupling installed on your tracks? If not install one to give your tracks more
length. If you have one installed add another to give you...

Hi, hope this info helps. The only way to get an Argo out of water if it breaks through ice is backwards. Argos float down by the front because of the engine weight. So the front of the body will hit...

Hi I would like to ask you some questions first about your spacer. What type of tracks are you running plastic or rubber. Which axle was the spacer on.
There is not much of an issue with plastic...

Hi. If you want to know how to get a Argo out of the water if it went through ice there videos available on this site. I don't know where??
OK. If your Argo goes through the ice the easy way to get...

I have an Argo conquest. I have a trailer that has a 12ft deck 70 inches wide. At front of the deck I installed a eye bolt. At the front of the Argo below the rubber bumper below the winch there are...