Search:

Thank you, North Country! I will do that.

After I put the 2 new 21x11x8 22 Mag tires I had on, they?re actually shorter than the original tires by an inch or more. I don?t think I will have any...

I put on 2 new tires today and started servicing it. I greased every zerk I could find but I could only find them on the outside bearings. No zerks inside the tub. I had to pull the carb off and...

So I received the manual with the Argo. It?s a 1987 model with the 18hp Kohler engine. It only has 192.5 hours on it! A mouse has gotten in it and chewed a few wires though, so I?m going to have to...

Well I guess you can say I?m afflicted with the sickness now? I bought another project lol. My wife sent me a facebook marketplace post for a Argo. They were asking $1200 but I offered $1000 and they...

Fantastic, thank you sir!!!

Thank you sir! My belt was way too loose to start then. It was floppy in there before.

Hi guys, I?m in the process of installing a new engine and the mounting bolts don?t line up. I?m going to have to drill new holes and I can?t find the measurements for how far to space the center of...

Johnny Boy- that never crossed my mind, that?s a darn good idea! Thank you sir!

Thank you! I have been thinking about what I?m gonna do for a throttle cable. I was starting to think about an adapter but I?m not sure what I should do yet. I really want to save all my money for...

I test fitted the Honda today. If I follow through with this smaller engine, I will have to redrill the mounting holes and because the Honda?s carburetor is bad, I put the 32mm carburetor that I...

Well that didn?t pan out. The kohler has a tapered shaft. Next best option I have right now is to put in a Honda GX-340 11 hp engine to get me by. Only problem is, it?s recoil start. I can get a...

I finally made the time to pull the engine out of this thing. It was a big pain in the butt to get the drive clutch off of it. It took me half an hour or 45 minutes. I had to hit it with PB blaster...

Well after lots of research I finally found a company that imports v-twin diesels. I haven?t bought one because I am still trying to make my mind up.

http://www.a1biofuel.net/22WHG-1-Web.html

I installed the new choke cable and the carb is flooding out. I need to do more research on the type of jet kit I need and start trying smaller jets for the idle. Also the float is starting to...

I ordered a choke cable assembly for a honda rancher because the cable and the housing looked like it will work for the application. It was $10 so we?ll see if I can make it fit. Should work out...

I finally got around to installing the mikuni carb. It runs but doesn?t idle that good. I also need to order a new choke cable and spring. It?s rusted and gummy inside the sheath. But it sure sounds...

Well I went and bought a Mitsubishi Minicab because the add said it had a 3 cyl Kubota diesel. Well turns out it was a 4 cyl kubota and it?s way too big for the max. I knew it was and bought it...

Earlier today, I fired it up and adjusted the carb so it?ll idle again. I had the idle set too lean. I should probably install the mikuni carb already. My procrastination has over taken me this...

I cleaned up the ?new? carburetor and it?s all ready for the install. I?m gonna have to build an intake adapter. I imagine that I?ll just use 1- 3/8? exhaust pipe and make a couple flanges out of...

Well I finally had some success! I got the better of my two snowmobiles running! I had to clean the carb real good and then replace the drive belt. It still needs new skis and a few other things but...