I am also a resident in NYS I live about 30 mins east of syracuse and I'm still fiddling with my MAX but I have put it on the back burner b/c there really isn't anywhere to ride the thing. I have 40...
Type: Posts; User: golpher76
I am also a resident in NYS I live about 30 mins east of syracuse and I'm still fiddling with my MAX but I have put it on the back burner b/c there really isn't anywhere to ride the thing. I have 40...
I forgot to mention I did not buy mine from that website I just used it for a reference and a picture I actually bought mine at tractor supply company and they were about 3-4 dollars each but are...
These are the one's I use you just need a small wrench (which I carry with me) to losen and remove them.
McMaster-Carr
http://images2.mcmaster.com/Contents/gfx/large/2554kp1l.png?ver=20166758
I also used to have one of those honda 185 3 wheelers when i was 12 or 13 it was an amazing machine i had 25" wooly booger tires on the back and i had the intake hose and air box sealed so i could...
you're right guy they are 4.75 I have been doing some searching and found a lot of things that have 5x4.5" and they all seem to have a 1.5" axle and range between 28 and 33". I am just going to...
Awesome I am going to order some and try it out thanks for the link.
what is gflex and where can i get some? I'd like to try it on a few holes that I have in my tub.
Anyone else going to post up location so we can find some fellow riders that are close?
Has anyone ever considered using chevrolet axle shafts out of older vehicles with a 5x4.5 bolt pattern like in mid 80's s-10's and 2 wheel drive 1/2 ton pickups. The axles are heat treated 1.5"...
First off thank you guys for all the suggestions. One of the sprockets on my t-20 the teeth look like shark fins. I just really started looking over the sprockets/chains this weekend and that is...
I realized that I needed new outer bearings and new bushings as I don't think they have been changed in a long time. I replaced the worst one this weekend and realized that the axle has grooving in...
So after my first short ride this weekend I realize I have some issues. It ran very good and the clutch is top notch now but should I be getting a lot of frame twist when going over uneven terrain? ...
So after some troubleshooting and trial and error I have a 1/2" hole drilled in each activator puck in the clutch and I filled the holes with lead. It is now engaging 100% so..... 50 dollar clutch...
Got my first ride in last night since I got the motor in and I changed the clutch spring in my duster. It moved around a bit but still wasn't engaging quite right but I took my son for a quick lap...
Well unfortunately no first ride but it runs amazing. I picked up a duster clutch from a friend for 50 dollars but it's off an old snowmobile. I am going to be ordering a pink spring as soon as I...
sweet ty racer i figured it out myself about 40 mins ago so I am all set and getting fueled up and ready for my first ride. ty again sir.
the wire in the pic i posted goes to solenoid on my carb. I am assuming this is why I am not getting fuel but I still don't know where it should be hooked.
Lets go guys lets fill this map up so we know who is close to us so we can ride with them .
This is the pic racerone and yes I hooked my kill switch up to the bolt on the shrowd it just won't pump fuel for some reason but all hoses etc are new.
here is a pic of the wire in question.
...
Ok so I got the new engine in and I can't get it to pump fuel I hooked a ground wire up the the ground on the shrowd and the red wire to my batt. It turns over but there is another orange wire there...