I don't swim much. Just deep enough to use my trolling motor. How many ply are the tires?
Type: Posts; User: EWS
I don't swim much. Just deep enough to use my trolling motor. How many ply are the tires?
I was thinking about replacing the tires on my 2007 Argo Avenger. It came with the Goodyear Rawhide 3's, but I was considering using ITP Mudlites. The tire size is 25x12x9. The Mudlites are 6 ply....
One of the plastic hood retaining pins on my 2007 Argo Avenger always bend while riding, causing the hood to slide off the pin on that side. It's the side closest to the muffler. I bought the...
I have started the Kohler 17hp engine several times with a rope. You must be careful though.
I have my mount welded, now I just have to add the plywood. I'm hoping to give it a test run soon.
That's only 2 inches longer than the motor I have now. I need to get the motor about 6 inches deeper. I'm thinking about making up an outboard motor mount that will fit in the hitch receiver....
I have a 2007 Argo Avenger with the Argo outboard motor mount that mounts off to the side of center. Anyone using a long shaft outboard on this mount? If you are, is the prop getting deep enough for...
You need a support that goes from your hitch to the leg of your outboard motor. I've used a 10 hp. motor with this setup.
Hi Moose Hunter,
I'm glad that the instructions came through ok, It's really not too difficult to install.
Ride Safe
EWS
Hi Moose Hunter;
I had a problem with my email account. It's okay now, but I need your email address again. I will try and send the instructions tomorrow.
EWS
Hi Moose Hunter;
I have the instructions for the canopy, I recently put a canopy on my 2007 Avenger. Can I email the instructions to you?
EWS
Hi plott hound;
I keyed the axles & sprockets on my 1984 argo, cost me $ 150.00 dollars for complete job. It was annoying having to unload everything in the back to replace the darn roll pins. I...
Hi Racerone3;
I had a 1984 argo 8x8 with a Kohler twin 17 that I used for work & play for 23 years. When I sold the machine it was on the third set of spark plugs. It was a very dependable motor....
Hi Guys
Anybody using a hitch rack? I've looked at some factory types, but can't decide on the length.
They range from 48 to 60 inches in length. I'm also considering designing my own, having the...
Gave the argo a test run on Saturday, on land and in water, everything was good,no rumble. Thought I would let you guys know.
Ride Safe
EWS
I decided to loosen both idler chains to further check the idler shaft bearings, everything seemed fine so I tightened the idler chains, spun the wheels & the rumble was gone. Probably had the chains...
When I rev the transmission in neutral it is okay. The oil is clean, I change it at the required intervals. I also checked the idler shaft bearings & found no movement in them. Have you ever seen a...
Hi Guys;
I have a 2007 Argo Avenger with 115 hrs of use. Lately I hear a rumbling noise whe the machine gets up to a speed of approx 5 km/hr, but when reaching a speed of approx10 km/hr & higher it...
Danybernier
I had a 1984 Argo with those awlful spiral pins. I tolerated the pins breaking for as long as I could, Didn't like unloading the Argo to replace the back four pins,then I decided that...
Hi Lewis
The mods turned out to be very effective, I'm pleased. The wiring and connector also went well. I tried to post pictures of the mods but couldn't post them, must have done something...