Turbochargers?

[Stonewall]

Has anyone ever put a turbo on an engine like we use in our 6x6's? I was watching videos on youtube and ran across this guy who put one on a Kohler 22 HP.



I was thinking about trying this with my Kohler 20, since these turbos aren't extremely expensive (around $200 on ebay), but I wanted to get some opinions and thoughts first. So try it or no?

[jpswift1]

If I was going with forced induction, all forged internals would be on the top of my list, first and foremost. I know Performance V-Twins has been experimenting with some supercharger options for V-twins. It's pretty cool that these innovations are coming about.

Performance V-Twins

[truckinwagen]

you need to be very careful with forced induction, it is really easy to lean out and blow up the motor under boost.

if you are running a blow through(carb after turbo) you need to be sure the turbo is set up for being pressurized.
if you are running a draw through(carb before turbo) you need to be sure the turbo has the right kind of seals in it(I think carbon seals are what you want, but don't quote me on that)

you also need to set up a rising rate fuel pressure system, so the carb will deliver more fuel as boost rises, which means a new higher pressure fuel pump, and a fuel pressure regulator.

there is lots of power to be had with forced induction, but you need to be careful not to destroy your motor(and it happens fast, just a minute with a bad tune will toast a motor)

I would supercharge one if you really want forced induction, they are alot easier to set up(less dynamic variables) and you dont have to worry about the kind of seals to run a draw through(by far the easiest way to do it)

just my 2 cents

-Owen

[spookum]

after extensive searching for a snow machine aplication of 600 CC you can learn alot from that crew. First get a small turbo that spools fast like a TDO2 or TDO1... common on streat bikes or small twin turbo tuners second, (but before you mount this) you can get a stand alone sytem or Exhaust gas tepatures (EGT) and O2 sensor (so you can easily see rich or lean) and boost peramaters... it will run you about 300 bucks to keep you from blowin your moter up! also, be ready for an inner cooler (keep you from melting your pistons) and wire the oil into the turbo and through a cooler, and you HAVE to keep an eye on that.

also you need to see if you are ready for a turbo:

step one, give your closest friend a 100$ bill

step two make him lite it

step three if you hand him another 100 dollar bill, you can have a turbo, but if you flinch i would stay away from them, they get expensive. and if it works? you get major cool factor, but will your belt hold up? what about any old chains?

good luck and you would be my hero if you can make it work

[Stonewall]

Anything fun or cool is going to be expensive, I learned that quick..... I wasn't angling for forced induction in general, but speciffically a turbo mainly because I don't like belts and there is something about the whistle of a turbo spooling up.....

The turbo I was looking at is a K03 like the one in the video:98-99-00-01-02-03 VW PASSAT 1.8T K03 TURBO CHARGER | eBay It will be a blow through system, most likely using a Kohler 2 barrel carb.

Intercooler is not a problem, it'll go in my duct system for the engine cooling.

I'll gladly take suggestions for what EGT/O2 monitoring system would be best.

Do I really need forged internals? I thought a turbo just moved the air and fuel through quicker not increase the combustion ratio.

Machine will be getting new diamond chains soon.

I would like to eventully try and ditch the belt drive alltogether. IMO a fluid coupling (stand alone torque converter) is the way to go.

[spookum]

if you are for reall about this buddy, ill give you a hand and even do the math on your 23 HP engine to find how much boost you can run without exceding 9:1 compression. Ill also figure out how much gass you have to use to keep the stochemetric ratio of aobut 14.7:1... let me know

[smog]

Has anyone ever put a turbo on an engine like we use in our 6x6's?

I would skip the turbocharging mess and just use a 4 strokes snowmobile engine. it's small, powerful and reliable.... and some are turbocharged.

[Stonewall]

I think that this turbo is the one I will probably use. It's the right size for the 624cc engine, and has the built in wastegate.

I wonder if the turbo oiling system could be plumbed to work with the engine's oiling system?

I don't know about a closed loop injection system, but TBI is definately a possibility. My '08 Honda Rancher has TBI, and it has loads of power in just a 419cc engine. I have thought about the TBI before, but we need another thread for those ideas lol.

I will have a look around for a good O2/EGT system.

This is going to be fun!

[spookum]

what kind of turbo? the auction ended?

[BREEZE]

eBay My World - universalturbokitsales