Noel All good, I cut 1 inch of each track, reinstalled aired tures up to 5 lbs and now have 1.5 inches of sag on 2nd and 3rd tires
Happy guy now. Thanks for everyone's imput , much appreciated....
Type: Posts; User: 28560HUNTING
Noel All good, I cut 1 inch of each track, reinstalled aired tures up to 5 lbs and now have 1.5 inches of sag on 2nd and 3rd tires
Happy guy now. Thanks for everyone's imput , much appreciated....
Ok Noel what do you think??? Shorten the track/belting????? 1Inch should be enough I think
Question what is everyone's idea on track sag and air pressure when installing tracks??
All my tires are indexed,I'm at 7psi on all 8 tires on my conquest with Adair pro series tracks
and have a...
Just wondering if anyone has used other tires besides the 22x10-8 Carlisle at189 , with their tracks. Whether Argo plastic tracks or even Adair tracks. Jusy looking for something not quite as pricey...
Help was looking at my conquest and noticed the 30 amp fuse burnt and melted. Replaced fuse and ran all good charging fine now. Any ideas why it would blow the fuse???? Was running and starting fine...
Tires have all been indexed I'm going to check it again but I think I'm bang on larger tires in middle smaller on the corners.air pressure all the same.
All right side chains are perfect so...
help chain loose with tracks on
Well I ll try and keep this short, while changing the axles on my conquest when I was done and in the air I ran it and noticed that the chains on left rear and left 2 nd from rear are loose on top...
Ya thinking about a bit of an enclosure, so I can throw supplies up there when I go hunting and a bit of a rain guard. I realize that the rops has downfalls as well top heavy poor stability in the...
Just thinking about a rops to my conquest, it will be shop fabricated not bought, my only concern is how tall are they??How many inches is from the tub lip or mounting area to the top of your rops??I...
Crisis solved yes lossen flanges and pry over bearing flange.Loosen outter bearing screws and drive axle in .Slide pitman arm puller over bearing hit with impact and wow off the bearing slides .
avenger inner bearings seized to axle
Well help had a guy bring me his avenger for repair andd myself having a weak moment agreed to help him out. It has 3 bad bearings with all the inner bearings seized to the axle. I got 1 out so far...
Hey just looking for some imput.Does anybody knoe what these escargo tracks weigh? ??? I myself have a set of 18 inch Adair tracks thst used to belong to RD.I am very happy with.My hunting buddy...
Adair tracks and big thank U
Just a quick note and numerous thank yous to Roc Doc, Tim and Mike at Adair. I purchased RD s old 18.5 tracks and with all the help from the Adair boys I rebuilt them (trust me lots of phone...
I repair bthis stuff firva living, Companies that repair this stuff may be called fibrenew or colorglo.If you just want to seal it up urself try goop(can be purchased at walmart or canadian tire) or...
Ok boys what s the latest on sprockets I have been letting the fronts sprocket s and the idler sprockets float. I have not been using the set screws on those 2 spots but all other sprockets aligned...
On my 96 conquest in lowgear I have a constant reciprocating noise it like a knock almost.High gear and reverse normal trany hum.Any ideas is the trans coming out for a tear down ????? Oil is clean I...
Hey fellas looking for some help.i have a conquest while looking thru the parts shed i found the old top/canopy/canvas cab off of my magnum.looking for pics or old instructions on the install.just...
ok gents drained oil down approx 1/4 inch from full mark and still getting oil pushed up into filter housing
No steep situations.oil level is just a hair over full do you think this would do that?????????
NOTICED THAT THERE IS ALWAYS OIL IN THE AIR FILTER HOUSING.SEEMS TO BE COMING OUT OF BREATHER TUBE THAT IS ATTACHED TO BOTTOM OF AIR CLEANER ASSM.COMP IS GOOD 175 PSI,OIL LEVEL ALWAYS GOOD ALL LOOKS...