6x6 World

Max 2 project

johnnova — Wed, 04 Jun 2014 12:57:39 +0000

by: johnnova

Description: Installing the middle axle and triple sprocket

Max 2 project

johnnova — Wed, 04 Jun 2014 12:57:35 +0000

by: johnnova

Description: I used a level from my table saw to check the jackshafts. it actually worked out pretty good and I also checked it with a tape measure after it was perfectly level.

Max 2 project

johnnova — Wed, 04 Jun 2014 12:57:32 +0000

by: johnnova

Description: made some new gaskets for the bearing flanges.

max 2 project

johnnova — Wed, 04 Jun 2014 12:57:28 +0000

by: johnnova

Description: installing the other jackshaft.

Max 2 project

johnnova — Wed, 04 Jun 2014 12:57:25 +0000

by: johnnova

Description: New inner bearings, this is the rear one under the engine it has a right angle grease fitting that some what helps getting at it for maintenance.

max 2 project

johnnova — Wed, 04 Jun 2014 12:57:18 +0000

by: johnnova

max 2 project

johnnova — Wed, 04 Jun 2014 12:57:14 +0000

by: johnnova

Description: new studs in the transmission. The bolts were loose and almost cut the old ones in half.

Max 2 project

johnnova — Wed, 04 Jun 2014 12:57:10 +0000

by: johnnova

Description: new springs and adjuster bolts

max 2 project

johnnova — Wed, 04 Jun 2014 12:57:07 +0000

by: johnnova

Description: installing the jackshafts

Max 2 project

johnnova — Wed, 04 Jun 2014 12:57:03 +0000

by: johnnova

Description: installed a 2 barrel carb on the 18hp briggs along with new valve springs and retainers. I also added the timing advance key and I am in the process of disabling the governor

1 comment

Max 2 project

johnnova — Wed, 04 Jun 2014 12:36:44 +0000

by: johnnova

Description: cleaned the tub out with some citrus based cleaner, the bees loved it. I had to hose it down and spray it with simple green to finish it off and drive away the bees.

Max 2 project

johnnova — Wed, 04 Jun 2014 12:36:40 +0000

by: johnnova

Description: Frame out and time to clean the tub up

Max 2 project

johnnova — Wed, 04 Jun 2014 12:36:35 +0000

by: johnnova

Description: taking the top body off

max 2 project

johnnova — Wed, 04 Jun 2014 12:32:43 +0000

by: johnnova

Description: more parts and misc junk

Max 2 project

johnnova — Wed, 04 Jun 2014 12:32:39 +0000

by: johnnova

Description: parts everywhere in the tub

Max 2 project

johnnova — Wed, 04 Jun 2014 12:32:30 +0000

by: johnnova

Description: Starting to take apart the max2

Max2 splined axles

johnnova — Wed, 04 Jun 2014 12:32:26 +0000

by: johnnova

Description: here are the axles that came with the project. they were in pretty rough shape when I got them and were just tossed in a metal bucket. it looks like who ever took the machine apart had a hard time. The axles were full of dents from hammering the sprockets off and bearings and were rusted up a bit. One of the axels was also broken right next to the spline where the bearing sits, that one was replaced with a new axle

Internal muffler

johnnova — Wed, 04 Jun 2014 12:32:21 +0000

by: johnnova

Description: When I got the project machine it was also missing the internal muffler. I waited a while for them to find this at Muddox. They had just moved and were still unpacking trailers when I placed my order for parts.

Bearing cages

johnnova — Wed, 04 Jun 2014 12:32:17 +0000

by: johnnova

Description: Side view

Bearing Cage

johnnova — Wed, 04 Jun 2014 12:32:10 +0000

by: johnnova

Description: This is one of the new front bearing cages for the max2

bearing cages

johnnova — Wed, 04 Jun 2014 12:32:04 +0000

by: johnnova

Description: Before I started installing the new bearing cages on my max2 I installed the outer bearings and flanges. I also used all stainless hardware hopefully it will last many years.

max 2 sprockets

johnnova — Thu, 13 Feb 2014 08:31:27 +0000

by: johnnova

max 2 sprockets

johnnova — Thu, 13 Feb 2014 08:31:24 +0000

by: johnnova

max 2 sprockets

johnnova — Thu, 13 Feb 2014 08:31:19 +0000

by: johnnova

max 2 sprockets

johnnova — Thu, 13 Feb 2014 08:31:09 +0000

by: johnnova

max 2 sprockets

johnnova — Thu, 13 Feb 2014 08:31:04 +0000

by: johnnova

max 2 sprockets

johnnova — Thu, 13 Feb 2014 08:31:01 +0000

by: johnnova

max 2 sprockets

johnnova — Thu, 13 Feb 2014 08:30:58 +0000

by: johnnova

max 2 sprockets

johnnova — Thu, 13 Feb 2014 08:30:54 +0000

by: johnnova