6x6 World

Tracks

Dexter59 — Sat, 12 Oct 2019 23:07:31 +0000

by: Dexter59

1 comment

tracks

Dexter59 — Tue, 12 Jun 2018 15:37:54 +0000

by: Dexter59

Description: I probably shouldn't drive this on the good grass.

Tracks

Dexter59 — Tue, 12 Jun 2018 15:30:44 +0000

by: Dexter59

Description: Harbor freight bender and I became good friends.

1 comment

My channel track project

Dexter59 — Tue, 12 Jun 2018 15:08:41 +0000

by: Dexter59

Description: Side view. The lump at the bottom is extra belt that I haven't cut off yet. Still trying to decide how much sag should be there.

1 comment

My channel track project

Dexter59 — Tue, 12 Jun 2018 15:08:37 +0000

by: Dexter59

Description: Front view of the max with its new tracks.

1 comment

Tracks

Dexter59 — Tue, 12 Jun 2018 15:08:32 +0000

by: Dexter59

Description: Ended up going with a 2" wheel spacer. I had built 6 5" inch ones like you can buy at Richards. I should have done some more checking before I waisted my time and money making them. I only needed 2". I was going to cut my 5" ones down and reweld them but this turned out to be easier.

My channel track project

Dexter59 — Tue, 12 Jun 2018 15:08:27 +0000

by: Dexter59

My channel track project

Dexter59 — Tue, 12 Jun 2018 15:08:22 +0000

by: Dexter59

Description: My temporary track assembly table.

My channel track project

Dexter59 — Tue, 12 Jun 2018 15:08:18 +0000

by: Dexter59

Description: One of the completed tracks.

My channel track project

Dexter59 — Tue, 12 Jun 2018 15:08:13 +0000

by: Dexter59

Description: My belt arrived. 1 roll 6" wide and 1 roll 4" wide

My channel track project

Dexter59 — Tue, 12 Jun 2018 15:08:08 +0000

by: Dexter59

Description: All bent and holes drilled

My channel track project

Dexter59 — Tue, 12 Jun 2018 15:08:03 +0000

by: Dexter59

Description: This Harbor Freight bender and I became good friends.

My channel track project

Dexter59 — Tue, 12 Jun 2018 15:07:59 +0000

by: Dexter59

Description: 64 pieces of steel 20" long started out as 10' pieces. Lots of cutting

This is it.

Dexter59 — Tue, 01 May 2018 19:43:23 +0000

by: Dexter59

Description: Finally bent what I think is the perfect one.

My attempt at channel grousers

Dexter59 — Tue, 24 Apr 2018 18:57:00 +0000

by: Dexter59

Description: A few attempts. The top ones were bent on the hand bender but hard to get the channel side bent in the exact spot. bottom one was cut then welded.

My attempt at channel grousers

Dexter59 — Tue, 24 Apr 2018 18:56:55 +0000

by: Dexter59

My attempt at channel grousers

Dexter59 — Tue, 24 Apr 2018 18:56:49 +0000

by: Dexter59

Description: Is it high enough?

My attempt at channel grousers

Dexter59 — Tue, 24 Apr 2018 18:56:43 +0000

by: Dexter59

Description: This is one that I decided to cut the channel then bend and weld. It made it much easier to get the bend exact. I think this one is the pretty close to what I need.