Announcement

Collapse
No announcement yet.

Convert your ARGO Conquest bearings to HDI bearings

Collapse
X
Collapse
  •  

  • Upgrade your Argo Conquest bearings to HDI

    Well, I finally got this little project started. I think everything is going to work out good, but there is still some testing to do. I ran into a couple little issues, but nothing that can't be dealt with.

    Sorry about the length of the vids, it was hard to keep the time down on a project like this. I have only uploaded the first part so far, but PT-2 will be edited into this post tomorrow if possible.

    I have to say here that I'm NOT SURE if this will work with ALL Conquests. I have noted that some older Conquests have different Bearing Extensions. Mine has the ones that require both the inner and outer bearing retainer when mounting Bearings in the bearing extensions. Some Conquests bearing extensions have the inner bearing retainer built into the bearing extensions. It may work, it may not. To find out what you have, look at your machines front/rear bearing extension assemblies. If you only see one gasket behind your outer bearing retainers, you have built in INNER bearing retainers. If you see 2 gaskets with a plate between, you have the same assemblies as mine.

    PART-1 (Front/Rear Axle Conversion)


    PART-2 (Mid Axle Conversion)



    RD
    Tags: None
      Posting comments is disabled.

    article_tags

    Collapse

    Latest Articles

    Collapse
    • Adjusting Chains and Jackshafts on a Max II
      by Mike
      For anyone new to six wheelers, this is a short video showing you how to adjust the chains in a Max II. There are eight chains that need to be adjusted. The chains between the front and middle axles and the chains between the rear and middle axles are tightened using the ratcheting chain adjusters. The ones in the front are adjusted by pushing the adjusters down. The ones in the rear are adjusted by pulling the adjusters up. The remaining four chains are adjusted by moving the jackshafts. ...
      03-14-2011, 11:05 PM
    • Repairing a Grooved Axle
      by Planter Bob
      Do you have a grooved axle and a shallow wallet? Well, here's the ticket for solving the problem without burning up the Visa card.

      Repairing a grooved axle on the cheap: 1. Remove the axle. 2. Clamp it firmly in a smooth-jawed vice, with the groove about 6" from the jaws of the vice. 3. Using a wire brush in a 4" grinder, clean all the area in and around the groove, making it free of rust and gunk. Use a flat file gently on any high spots. 4. Use paper towels and wipe down the...
      09-15-2010, 09:07 PM
    • Upgrade your Argo Conquest bearings to HDI
      by Rock Doctor
      Well, I finally got this little project started. I think everything is going to work out good, but there is still some testing to do. I ran into a couple little issues, but nothing that can't be dealt with. Sorry about the length of the vids, it was hard to keep the time down on a project like this. I have only uploaded the first part so far, but PT-2 will be edited into this post tomorrow if possible. I have to say here that I'm NOT SURE if this will work with ALL Conquests. I have noted that some ...
      06-07-2010, 09:05 PM
    • Bronco Seat for your Six Wheeler
      by racerone3
      i've needed to redo the seats in my wild wolf for as long as i've had it. the seat back was the original and shot, and the bottom was something i had quickly thrown together. last week after months of my son begging me to take him for a ride in my old bronco, i finally got the back seat down from the rafters of my shop and bolted it in. later that night it dawned on me that it would make a pretty good seat for the Wolf. i checked with the place i'd gotten my seat covers form when i built the bronco...
      04-13-2010, 09:57 PM
    • Used ATV Buyer's Guide
      by Mike
      General - Purchasing your first six wheeler can be exciting and it is something that many of us remember well; Seeing it for the first time, the test drive, towing it home, taking it for a spin around the yard and realizing how quickly you can tear up the grass. But it can also be an intimidating process especially if you are not purchasing new. For some, a new six wheeler is simply out of the question. Whether it is financial concerns or simply that the six wheeler you are looking for is no...
      02-28-2010, 01:23 PM
    • Heatgun Body Repair Oxidation Video
      by REB181
      How to bring the shine back to your HDPE Polyethylene body. Works on any 6x6 or 8x8 HDPE body and is simple to do.

      http://s239.photobucket.com/albums/f...unbodyclip.mp4...
      02-12-2010, 08:50 PM
    View All
    Working...
    X