$75 Attex ST300D

[lewis]

Looking good there BD. Keep us posted with pics.

[rob63mess]

scrap abs

Hey i have alittle abs from a scrap wild wolf.... where are you located? I saw where you raced at Midway.... Crooksville by any chance?

[birddog1148]

Hey i have alittle abs from a scrap wild wolf.... where are you located? I saw where you raced at Midway.... Crooksville by any chance?

Yea Crooksville, been 2 years tho, 2007 late model rookie of the year and 4th in points
28a late model
Your pretty close!

[LarryW]

Does this look right? Or do the bottom corners need something done?

The seat back is to long. The seat back fits in the groove up a little. The bottom of the back starts on top of the cushion on seat. That whole board has to move up and probably cut some of the top.
Sorry I didnt post sooner but the question was hiding in the pictures and I didnt see it.

[birddog1148]

Thanks Larry!

[LarryW]

no problem.

Then the seat back is mounted to the engine cover. I just have them both sitting in my though but there are times when they do move around and I wish they are mounted. The seat set I use was already made when I got them but for some reason they weigh a ton. Thats why I never mounted them because together they are just too heavy. Not sure why, thick lumber i guess but could be water logged? But I cant get any water out of them. not sure but they are heavy.

[birddog1148]

In the garage finally!

Plus I got a new camera for my elk hunting trip and had to try it out.

[rob63mess]

I use to race there about 5 years ago. I live in Heath. If you need some scrap abs, let me know. I' give you some. You can grind it up for repairs or use it for plastic welding.

[birddog1148]

I use to race there about 5 years ago. I live in Heath. If you need some scrap abs, let me know. I' give you some. You can grind it up for repairs or use it for plastic welding.

Cool, thanks Rob!
What did you race and what was your#?

I used to have the 52ex 4cyl and the 28a latemodel.

[rob63mess]

I ran 4cyl. my number was 15M. I ran there in 2002 and 2003. I ran mostly at Muskingum after that.

[birddog1148]

I found a Comet TAV 30 clutch in my garage! Only good for 8hp tho.

[LarryW]

I found a Comet TAV 30 clutch in my garage! Only good for 8hp tho.

Also for a 3/4" belt.

[birddog1148]

My outer bearings seam to be Pressed on since I cant find any locking device ie set screw, clip, etc.
What do you guys think of these? I figure I will just make new axles as long as I am at it, the hole for the hubs on some are wallowed out.
Three Bolt Flange Bearings Hanger Ball bearings V-Belts

[LarryW]

My outer bearings seam to be Pressed on since I cant find any locking device ie set screw, clip, etc.
What do you guys think of these? I figure I will just make new axles as long as I am at it, the hole for the hubs on some are wallowed out.
Three Bolt Flange Bearings Hanger Ball bearings V-Belts

The bearings are pressed on. Personally I love them. I never have had any problems with the axles walking in/out. They(bearings) come off when you want them too. No messing with setscrews or eccentric locking collars. Great setup that works.

[birddog1148]

The bearings are pressed on. Personally I love them. I never have had any problems with the axles walking in/out. They(bearings) come off when you want them too. No messing with setscrews or eccentric locking collars. Great setup that works.

I dont have a press, already broke one housing

WHats the trick to getting them off?