Announcement

Collapse
No announcement yet.

part # for Dayco belt 980 bigfoot

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • #31
    Don,
    I don't think it would have to be very tight. Remember the older Argo style that used a couple of coil springs that pulled two sliders together. It was mounted but these could float on the chain.

    Comment


    • #32
      I found a link:

      Chain Tensioners

      Comment


      • #33
        jerrynuss,


        Ok, now I know what the free floating chain adjuster looks like that you posted about . Do you set the tension on this chain adjuster by tighting allen head screws , and this puts tension on the top and bottom chain ? If so , does it then slide back and forth until it finds the loosest section on the chain ?
        Last edited by mudbug3; 09-22-2008, 02:14 AM.

        Comment


        • #34

          Comment


          • #35
            jerrynuss ,


            Exellent pic jerry . Does this free floating adjuster need no adjustment once you install it ?

            Comment


            • #36
              It is like a big zip tie, push down on the upper block and pull up on the ties. Cut off the excess while leaving some to grab onto for adjusting later. I saw another design where a person uses two blocks and with channels for the chains and two grooves that a person uses the thick heavy duty zip ties to squeeze the blocks together.

              Comment


              • #37
                jerrynuss ,


                If this free floating chain adjuster works as planned ,,this would be the answer to the Hustler chain tensioner problems .

                Comment


                • #38
                  I have been thinking about trying the Snap Idle tensioners on the drive chain from the T-20. I even spoke with one of their engineers when researching chain tensioners. There is a foot per minute speed limitation on those tensioners....but I did not take the time to figure out if we would exceed that???? However, the engineer did say he had heard of them being used on AATV's with no problems.

                  I did post some updated pics of the front chain tensioners in mine. So far so good. I have not adjusted them at all after 2 all day rides with Mudbug. Also posted some new pics of my cheap and easy T-20 hold downs.

                  DSC00037 pictures from outdoors photos on webshots
                  Hammers should have warning labels.

                  Comment


                  • #39
                    George sent in a Dayco part number list so you can cross reference numbers and sizes. I put it in the Articles section here: http://www.6x6world.com/forums/gener...ive-belts.html

                    Thanks George!

                    Comment


                    • #40
                      BTW, I talked to JPSwift tonight on the phone and he took his original 980 belt up to Buffalo Bearing and they matched it up exactly. As soon as he gets it this week, we will have an exact part# to compare to. But there is for sure at least 1 belt manafacturer out there.
                      Hammers should have warning labels.

                      Comment


                      • #41
                        Any update on that belt?

                        Comment


                        • #42
                          You guys end up having any luck on this belt? I'm dealing with a 980 with stock 18 Briggs too.
                          1984 Hustler 980 and some other toys that won't even swim.

                          Comment


                          • #43
                            Call Buffalo Bearing and tell them that Jeff (the guy with all the 6 wheelers sent you). They can sell you the correct belt. Just tell them it is the same one that they ordered for Jeff for his Hustler and you'll be all set. They're good folks to deal with. Here is their number:

                            716-874-1720
                            "Looks like you have a problem with your 4 wheeler........you're missin' two wheels there"
                            sigpic

                            Comment


                            • #44
                              Thank you much. I'll have to get with them.
                              1984 Hustler 980 and some other toys that won't even swim.

                              Comment


                              • #45
                                Glad to help. Since I don't recall the part number off hand, just have the guys at Buffalo Bearing cross reference Goodyear 1930V491 or Salsbury 704084 and you should be all set.
                                "Looks like you have a problem with your 4 wheeler........you're missin' two wheels there"
                                sigpic

                                Comment

                                Working...
                                X